If you do not want to have extraneous noise and screens in the cabin of your car, as well as if you are a real Meloman and want to enjoy true musical sounds - your car needs quality noise insulation. In this article we will tell you how to remove unnecessary sounds, or make noise insulation with your own hands and offer the selection of materials necessary for this work.

If the budget is limited how easier to make noise insulation

Do not try to make noise insulation throughout the car immediately, remember - experience comes with time.

Start work to eliminate noise with car doors.

If everything happens - do the floor.

The third stage of the work will be the ceiling, and then the trunk.

But, before starting all the work, think about what you want to get from your car - just improve the comfort of stay in the car, get rid of the squeak or listen to high-quality music.

Depending on the task, you will select and building material.

Tools required for work:

-Special construction hairdryer;

- Special roller (for pressing the material for noise insulation);

- Data for cutting the material of noise insulation;

solvent for degreasing the surface under noise insulation.

What materials are needed for noise insulation

vibroplast Silver

Wonderful material, well absorbing vibration, has good elasticity and flexibility.

This noise insulator is a polymer self-adhesive fabric in a hood with an aluminum foil, there is a markup in the form of 5x5 cm squares.

Vibroplast does not respond to the environment, has excellent anti-corrosion properties, it can serve as a sealant.

It does not need a heating when installing, it is easily installed on any surface with any relief, the thickness of it is only 2 mm, the proportion of 3 kg / m2.

It is possible to use for noise insulation of the floor, doors, roofs, sidewalls of the body, hood and trunk covers, for the instrument panel inside the cabin.

vibroplast GOLD.

The analogue of the Vibroplast Silver, but has a greater vibration insulation due to an increase in the thickness of the material - 2.3 mm, the proportion of 4 kg / m2.

Applied in the same places as Silver.

bimast Bomb

The best vibrating unit due to the multilayer structure in the form of a first layer of aluminum foil, then a bitumen composition goes, then a layer of rubber composition.

But it is necessary to heat the material up to 40-50 * s.

It has the highest efficiency, a wonderful material for speakers, has a thickness of 4.2 mm, the proportion of 6 kg / m2.

Used:

-For noise insulation of the front panel;

-For arches of wheels;

-When insulation over the silencer;

-When insulation over the cardan shaft.

splin 3004.

The material for sound insulation with its own adhesive layer has good thermal insulation properties, is well installed on vertical and curvilinear surfaces, does not absorb moisture, does not respond to environmental impact.

It has a wide range of operation at temperatures from -40 to + 70 * C, thickness 4 mm.

Used:

- while working with the shield of the salon instruments;

- Work with the arches of the wheels;

- Work with the doors and tunnels.

It is splen 3008 with a thickness of 8 mm and splen 3002 with a thickness of 2 mm.

The material is spilled in the second layer over the vibrop absorbing material, the glued surfaces must be pre-skilled - it will give a guarantee of the strength of the connection.

This material is applied on the doors, front and rear arches and on the sidewalls.

When working with adhesive ribbon, splen, to improve adhesion, the ambient temperature should be from +18 to 35 * s.

The protective layer should be accurately removed immediately before applying, the adhesive tape is applied without tension.

antiCrip Bitoplast 5.

Perfectly eliminates the symbols and brand in the cabin, as it is a noise absorbing and sealing material.

Made of polyurethane foam, has a sticky layer.

Waterproof material, as it does not decompose, is a durable, odorless, is able to maintain its properties at very low temperatures.

accent 10.

Sound absorber, as this is a playful metallized film, includes elastic polyurethane foam, has an adhesive mounting layer, good heat-shielding properties, is able to absorb up to 90% noise, works at temperatures from -40 * to + 100 * s.

The emphasis is used with the cap of the hood and trunk, with the partitions of the engine compartment.

madelin

It is used for sealing and in the form of decorative material, as it is made on the basis of black tissue, the thickness of the material is 1-1.5 mm with a glue layer.

It is used to eliminate the gaps between the decorative elements of the cabin and the body, to eliminate the gaps in the instrument panel, to seal the air ducts.

Hood Noise Isolation Work

No matter how hard you try to get rid of the noise of the engine, completely remove the noise of the motor will fail.

Basically, the work on noise insulation of the hood is done to improve the insulation of the engine during the cold period.

In order not to overload the hood shock absorbers, for noise insulation it is necessary to choose the easiest materials - the focus of 10 mm and the Silver vibroplast.

For vibration insulation, the Vibroplast Silver is well suited for thermal insulation - accent, as the emphasis will keep the heat of the engine in winter and will not light up from the heat of the engine, as the focus is hot-stroke.

Do not throw away the factory thermal insulation material, as the noise insulation should be the help of factory noise insulation, and not its replacement. Those. You must choose such a thickness of the accent, so that after the production of work, your own hands, you could wear a factory noise insulation.

And if there is no factory noise insulation on your car, then you must use the thick insulating material at 15 mm.

How to make noise insulation car doors

Even the most elementary noise insulation will improve the sound of music in your car. You can use vibration insulating material Vibroplast Silver or Gold. The material is pasted on the inside of the door against the column.

In order not to drain the door to prevent sagging, it is reasonable to choose the weight of the material, and if you are particularly demanding about the audio system, make noise insulation at least four layers.

The first layer is glued from the inside of the door Vibroplast Silver or Gold over the speaker through a special hole in the door.

The second layer is glued with vibration insulating material. 4 mm splen.

The door insulation is on the outside, it is necessary to fully stick all the technological holes, create a sealed door.

The rear doors are made as well as the front, but if they do not have speakers, you can do without a smaller number of layers.

How to make noise insulation ceiling and roofing machine with your own hands

If you are annoying the noise of rain, use the Gold or Silver vibroplast, but avoid weighting ceiling.

It is possible to recommend splen 4 or 8 mm, you can make a lining in two layers - the main thing is to be able to carefully remove, and then return the ceiling trim in your place.

Noise insulation of the floor of the car do it yourself

In order not to hear the noise of the irregularities of the road, blows from the stones along the bottom of the car - to put the vibration insulation of the bimash bum on the floor, put a splenple 4 or 8 mm on top.

If it is spilled big thickness to lay uncomfortable, put it with a smaller thickness in two layers, but it is important to put the splenple without gaps over the entire surface.

And the Arches of Queens from the Salon side to put the bimst bimaster with vibration insulation.

Noise insulation trunk, wheeled niches and arches

There are particularly many extraneous noise and creaks in the trunk or at hatchbacks in the area of \u200b\u200bthe fifth door.

It is especially closely necessary to treat a niche of a spare wheel, completely plunder it with vibration insulating material.

All the trunk trim will be bitoplast.

For noise insulation of wheeled niche, you must first remove the factory plastic shoes, clean from the dirt, to apply the Gold vibroplast on the inner layer of the arch, on the reverse side of the arch, stick the Silver vibroplast and put the factory sceners.