The modern vehicle includes a mass of complex nodes, mechanisms and devices. During the operation of the car, they wear out and from time to time require repair or replacement. The gearbox is no exception, especially this concerns domestic cars. Undoubtedly, the procedure for removing the checkpoint is quite time consuming and takes a lot of time. Therefore, most car owners resort to the help of specialists. However, this event is fully fulfilled at home, which will allow you to save your money. This will be discussed in the article.

Tools assistants, fixtures and consumables

To remove and subsequent installation of the PPC you will need the following consumables and tools:

1. Clean rag.
2. Jack.
   
3. Passatia.
4. Mount.
5. Flat screwdriver.
6. Set of heads with extension cords.
7. A set of horn, end or wrenches.
   
8. Capacity for draining waste fluid.

You will also need an assistant, because it is quite difficult to perform this operation yourself.

Preparatory work that you need to remove first to get to the gearbox, step by step

To get to the checkpoint, you must first give access to the bottom of the vehicle, so it is necessary to raise. To do this, you can drive the car on a viewing slot, rack or lift it with a lift. Then do the following:

1. First necessary to remove the motor protection (mudguard), which by means of a socket wrench unscrew bolts fastening a mudguard. Next, remove the protection.
   
2. Then remove the right side panel of the motor compartment.
   
3. Thereafter, drain the oil from the PPC. To the oil was drained of quality, it is recommended to warm up the engine before draining, giving him a few minutes to work. Then put under the drain hole previously prepared container and unscrew the cork.
   
4. When the waste liquid drained completely be cleaned hole and the plug of contaminants whereupon twirl it back.
   
5. At the next stage we disconnect the vehicle power supply by disconnecting the negative terminal of the battery.
   
6. Next dismantle the air filter. For this it is necessary to disconnect the air supply hose, the crankcase ventilation and the air flow sensor. Do not forget to remove the case vozduhofiltra who dismantled instead of the hose, the sensor and the throttle valve.
   
7. At this stage must be removed from the vehicle starter. First, you need to unscrew the nut that secures the clutch wire tip that connects the starter motor and battery positive conclusion. Then remove the bolt from the contact tip. Now disconnect relay driving control wire traction unscrew nuts then remove starter.
   

Transmission 2110, how to remove, step by step guide

1. From the bracket, you must disconnect the gearbox off the drive and plug the cable speeds of clutch engagement, which pull the plug the cable from the clutch lever in the engine compartment. Next you need to loosen the shell nut cable on the gearbox. Hold the envelope and take out of the cable end bracket.
   
2. Now disconnect from the reverse sensor and speed sensor connector wires.
   
3. Thereafter, disconnect the torque reaction arm, which is attached to the buffer using the two nuts. When the nuts unscrewed, it is necessary to remove the clamp and remove cravings.
   
4. Next detach from the pivot rod shift actuator.
   
5. Then, on the cover of the clutch housing Turn off fixing bolts and remove the cover.
   
6. Now you can remove wheel drives. So that when installing does not arise, it is necessary to put a wooden plug. We assign to the side or remove the right-hand drive.
   
7. Next weaken the fastening bolts of the ball support.
   
8. Remove the lower cover of the crankcase.
   
9. We unscrew the lower bolt for fastening the gearbox to the motor.
   
10. Then hang the power unit with the help of the prepared stop. We dismantle the left support of the motor, unscrewing the fastening nut.
    
11. Having unscrewed the cppon and nuts fastening bolts that fasten the back of the engine to the body, remove the back support.
    
12. We insert a screwdriver between the clutch crankcase and the cylinder block, we move the box from the guide bushings.
    
13. Weching the gearbox in the greatest possible way, shaking it, then dismantle.
    

Gearbox 2110, how to install a gearbox after repair

The CAT installation should be made in reverse order. As you see, the work is not easy and time-consuming, but it is quite possible to fulfill it yourself, according to the instructions described above.

Tips Profi, driver actions after repairing the gearbox

In order for the PPC to serve for a long time, it is necessary to properly exploit it, in particular:

1. Do not start with slipping.
2. When switching speeds, squeeze the clutch until it stops.
3. Switch the transmissions sequentially.
4. Change oil timely using only one specific brand.
   

It is worth noting that when the first signs of the gearbox malfunction should be diagnosed as quickly as possible to diagnose the breakdown, followed by its repair or replacement. It is not recommended to exploit the vehicle if the CAT failed.