Corrosion or rust body is a patient the theme of any car enthusiast. If such an infection falls on the body of your car, and you will miss the time or do not notice corrosion, it is a malicious rust to stop the roots throughout the body and the bottom of the car and after a while you will see holes on the body of your favorite "horses". To prevent the spread of rust and remove it, the car enthusiast should take into service various ways to deal with rust.

What is corrosion

If you at school did not skip chemistry lessons, you must remember that corrosion is the result of the interaction of metal with water, air, with chemical reagents.

Finding on the metal, the chemical reaction occurs and the result of this reaction is the oxide of iron and hydrogen.

And since your work machine is in constant contact not only with water and air, but also with chemical reagents (especially in winter) we get rust on our car.

Anticorrosive processing can prevent corrosion on the car.

Modern car body consists of a thin steel sheet on which a thin layer of paint coating is applied.

Any bulk or scratch leads to a violation of the layer of paintwork and in this place there is direct contact with the environment. The task of anti-corrosion processing is to eliminate direct contact with the aggressive medium.

Anticorrosion treatment types

There are many methods of anti-corrosion processing, in this article we present the following:

• to effectively repulsion water from the surface of the machine, the protective coating of Ceramic Pro has proven itself;
• it is good in operation Dinitrol 479 - he has established itself in the form of protection of the body from corrosion and noise insulation;
• to avoid the appearance on the body of chips and small scratches - use the carbon type vinyl film;

• preparing for the Russian Winter, to protect the bottoms from chemical reagents, make a car nise wax;
• you can advise a very reliable but dear way to protect the car from corrosion - spend galvanizing the bottom of the car;
• there is another electrochemical wayites from corrosion, but feedback on this method is contradictory, and the money will throw away the money.

Buying a new car, we are reported that the car has passed all the necessary anti-corrosion processing.

But the fact is that not all cars have high-quality anti-corrosion processing.

German and Japanese car manufacturers have proven well.

Manufacturers qualitatively cover the bottom and wheel arches with Dinitrol 479, paints and varnish materials have good water repellent properties, high-quality galvania is used. Therefore, cars of these manufacturers and through a quarter of a century on the roads, will give odds to our domestic cars or such as Chinese cars.

Car lubers know that the body begins to rust in the most problem places, namely:

• rust corrosive thresholds;
• wheeled arches;
• quickly disagree the locations of the details.

Sophisticated above said if you want to extend your car's life, do not forget to make anti-corrosion processing with one of the above methods.

And if you cheated and traces of rust appeared on the body, you will have to work hard.

Corrosion of the car body, what to do with rust

Answer one, remove rust.

But if the slightest chill paint appeared, the chief need to be immediately removed. Eliminate the chip in the following ways:

• with polishing, if the damage is very small and does not reach the metal;
• with painting, this is necessary in the case of a deeper chip to the soil layer;
• if deep cracks appeared - cracks need to be treated, painted, apply varnish and polishing.

You can advise motorists more often wash your cars, because the scratches and chips can be viewed under mud and dust, which will later lead to rust.

Scratchs and chips are noticeable on a clean car and you can polish the shallow chips on time or close them with a clear varnish.

If there are cracks to the ground and metal on the car, to close them, it is necessary to choose the desired color of the paint and varnish.

If corrosion or rust appeared on the car, the rust converter must be purchased to combat it.

You will have to work hard and carry out the following actions:

• with the help of sandpaper or grinding disks of medium grain for a drill, it is necessary to clean the damaged part of the machine;
• you can handle the anti-corrosion composition. Preparations such as WD-40, Rust Killer, Rust Treatment can dissolve iron oxide and degrease metal;
• after the damaged surface was processed, it is necessary to sharpen it, apply primer, paint and apply lacquer;
• polish the place of your work.

If you doubt success, you invite specialists.

Professionals Repairmen will select the necessary shade of paint, produce high-quality polishing and you will not be able to find the place of your ex-rust.

The galvanizing of problem seats is done at home, in this case, on problem areas, zinc settles a thin hoist.

How to process your car zinc, we will tell in the following articles.