Correct operation of the vehicle is ensured as the quality of its components, and applied on expendable materials and liquids that need to be timely change. This also applies to the oil filter Lada Granta, which varies with motor oil. You can perform this exercise on their own, to use the instructions below. About this further in the article.

Oil Filter Lada Granta, the device and the appointment of

Before installing the Lada Granta a new filter element, it is necessary to understand how best to choose the components. Purpose of the oil filter - purification engine oil wear particles produced during the friction elements, as well as unburnt solid fuel particles.

In most cases, the oil filter is a metallic glass, wherein the filter element is installed, assembled in the form of bellows, as well as two protective valve - and an anti-overflow.

Oil filters Lada Granta, popular manufacturers of quality filters, comparative analysis, which filter to choose

The most common manufacturers of filter materials that are allowed to be mounted on the Lada Granta - Union, Knecht, Mann, Renault and others. One of the best deserved filters is considered an original filter Renault 7700274177 and its analogs.

However, there is a risk to buy a fake, so it is advisable to buy products in specialized stores, as well as to request certificates on it. Imported consumables are many, so we can use domestic filters made for VAZ cars.

Engine oil Lada Granta, which oil is suitable for Lada Granta

The producer recommends to fill in the VAZ Lada Granta engine following engine oils:

How much oil need

According to regulations of the oil filter changes along with engine oil. Manufacturers are advised to carry the Lada Granta replacement lubricants 10-15 thousand kilometers. vehicle operating conditions directly affect the time between replacements. If the vehicle experiences a reinforced load, the period of application should be reduced by 2 times. Fill the engine must LADA Grant 3.2 liters of lubricant.

Tools, fixtures, consumables

To replace the engine oil and oil filter, you need the following tools and materials:

1. Funnel.
2. Clean rags.
3. Capacity to drain.
4. Puller for the filter.
5. Fresh engine oil.
6. A new oil filter.
7. Set of wrenches.

Choosing a workplace

For the convenience of work, it is necessary to drive the car on a viewing hole, rack or lift using the lift.

Safety precautions when working with hot liquids

Since the replacement of oil and filter carried on the engine is hot, care must be taken when loosening the drain plug, to avoid merging of burns with hot liquid. Work only with protective gloves. Remember that the used oil to drain to the ground is prohibited.

How to drain the oil (gradual progress)

1. First of all, we open the hood and unscrew the bay stop so that the oil is better than the glass.
   
2. Next, we unscrew the drain plug to merge the spent lubricant liquid.
   
3. We substitute the prepared container for draining under the motor.
4. We are waiting until the oil is completely stolen.
   
5. Spin the filler plug.

How to remove and replace the oil filter (step by step instruction)

1. Using the puller, unscrew the oil filter.
   
2. If there is no special key, try unscrew the filter with your hands or use the screwdriver - a strap, chain, a flat screwdriver and so on.
   
3. The place where the filter was located, wipe the pure cloth, so that the dirt did not get into a new lubricant.
4. Next, we take a new filter and half fill in new oil.
   
5. Sealing gum should also be lubricated.
   
6. Oil filter is twisted manually effortlessly until the gum is touched to the cylinder block. After that, the housing turns to ¾ turnover.

How to pour new oil

To pour new oil, it is necessary to take a fresh lubricant and pour with a funnel to the appropriate neck in the subcontrol space. Next, tighten the filling lid and run the motor for a few minutes. Then check that there is no leaks anywhere.

How to check the oil level

1. To check the level of engine oil, you need to stop the car on a flat site and drown out the engine.
2. Next, we are waiting for 10-15 minutes so that the oil is fully glass into the crankcase.
3. We use the oil dipstick and wipe it with a clean cloth that does not leave the fibers.
4. Install the probe back for a few seconds, after which we take it out and see the result.
5. Right is considered the level between the marks " mIN." and " max«.
   
6. If the oil level is insufficient, put it up to the norm.

Tips Prof.

Throughout the period of operation, the Lada Grant, however, like any car, it is necessary to monitor the quality of engine oil all the time and make it timely replacement and replacing the oil filter.