According to the manufacturer's regulations, in the car of Nissan Almera with automatic transmission, it is necessary to change the oil every 60,000 mileage kilometers, and from the manual transmission - every 90 thousand. You can do it yourself or contacting the specialized car repair shop. About this further in the article.

Why change oil in the gearbox

In any vehicle, regardless of the model and brand, including in the car, Nissan Almera, the oil is capable of deteriorating and lose its properties, wear products are accumulated here and additives are produced in it, and in the winter it is thick. As a result, the CAT may fail, and, as you know, the repair of the box can not be called cheap. To avoid this, it is necessary to replace the oil in a timely manner.

Oil automatic transmission of Nissan Almera, which oil can be pouring, quality requirements

For Nissan Almera with automatic transmission, the original oil is most suitable, in particular ATF Matic Fluid D, it is possible to find it by Ke908-99931.

There are alternative options - Valvoline Maxlife ATF, Petro-Canada Duradrive MV SUNTHETIC ATF.

How many oil in the automatic transmission of Nissan Almera

In the automatic transmission car, Nissan Almera enters about twelve liters of lubricant. For partial replacement, you will need about five liters of lubricant, for full - about ten.

Oil MCPP Nissan

In the CU of this model with the manual transmission, you can pour in fact any oil that meets certain requirements. Parameter - API - GL-4, viscosity 75W-80. The MCPP includes about three liters of oil.

Tools for work

1. Funnel.
   
2. Rags.
3. Gloves.
4. Pliers.
5. The key is 19.
6. Capacity for draining oil.
   

Replacing the oil in the MCPP Nissan, step-by-step instructions

1. Under the bottom of the car dismantle the protection of the crankcase and the checkpoint, if it is.
2. Inspect the checkpoint, especially pay attention to the anthers and glands of the left and right semi-axes. There should be no oil ilk.
3. Find the plot and drain plug on the manual transmission. The fuel simultaneously is considered an indicator of the lubricant level in the transmission.
   
4. Submold under the drain plug the container for the drain of the waste technical fluid, then unscrew the plug. We are waiting for about 10 minutes so that the oil merges completely. To speed up the process, warm the transmission before replacing.
   
5. Replace the sealing ring on a drain pass bolt to avoid leakage of oil as a result of wear of the gasket.
6. With the help of a special syringe, which can be easily purchased in any way in any auto parts store, fill the new oil.
   
7. Once the oil begins to overflow, the maximum level will be achieved.
   
8. In the bay hole, tighten the bolt and install protection in place.
   

Replacing oil in automatic transmission Nissan, partial oil change, step-by-step instruction

1. We raise the car with the help of a jack, drive on the observation pit, lift or overpass.
   
2. We find a hole for the drain and the bolts on which the pallet holds (it is a filter). The pallet does not need to be removed.
   
3. Wear gloves. Then we take the oil drain container and substitute it under the drain plug.
4. Using the key, unscrew the drain plug.
5. Remove the bolt to the end, after which the oil will begin to flow. To avoid burns, you should act carefully, since the liquid can be hot.
6. When the oil flows completely, measure its total volume.
   
7. Then pull the dipstick, insert the funnel into the hole and pour so much a new lubrication liquid as it was fused.
8. Insert the probe back.
9. Run the engine and wait five minutes. Next, we switch the transmissions from the PO position to the second and back, while holding back for a few seconds at each speed.
10. Next, we measure the use of the oil level and, if necessary, fill it.
    

Full oil replacement in automatic transmission, step-by-step instruction

The complete replacement of lubricating fluid in the Nissan Almer with automatic transmission is actually done in the same way as partial, but several more operations are added. After the point number, nine you must put on the gloves and substitute an empty container under the drain hole. Remove the plug and drain the liquid.

You need to pour about four liters of oil. As soon as the new liquid flows, we twist the cork and pour so many new oil as the old one.

Next, check the oil level, after which we bring the car, let it work for some time and switch the transmissions, lingering at each speed.

Tips Profi, how to find out the oil level in the automatic transmission

1. Take the dipstick.
2. Clean it that the dirt did not hit the system.
3. In fact, all auto oil level is checked after heating the gearbox and on the running motor. You need to pass 10-15 kilometers in the "Drive" position, then stand on a horizontal smooth surface and put the selector to the Parking position. Now you should give the Motor to work two or three minutes at idle.
   
4. I pull out the oil dipstick and wipe the EO with a clean rare without different threads, pile and the other.
5. Next you need to insert the probe back, hold five seconds and pull out again.
6. Check the oil level on the dipstick. Here you will see the designations, as a rule, in the form of notches for a cold ("Cold") and hot ("hot") method of checking and the corresponding maximum and minimum marks for each method.