The ignition lock is the primary switching element of the car electrical system, in other words, it is a moving blurring contact. Initially, the ignition locks also performed an anti-theft function, but today they are ineffective in this regard. Since the hijackers learned to hack even electronic locks, what to talk about ordinary ignition locks. When the ignition lock breaks, the car will be almost impossible. From this situation, there are two outputs - this is repairs, and replacing the entire ignition lock.

Ignition Castle Device VAZ 2110

VAZ 2110 Car Ignition Castle in the structural plan is not particularly difficult.

It is a fairly simple device consisting of two main elements:

• Anti-theft mechanical part (blocks when trying to start not native key shaft steering wheel and contact group directly the ignition lock itself);
• The contact part (provides current from the battery to consumers, including the starter).

VAZ 2110 ignition lock consists of the following details:

1. Ignition Castle Case;
2. Shut-off stitch;
3. Drive stitch drive;
4. Ignition lock contactor;
5. Block;
6. Springs;
7. Washers;
8. Cylinder;
9. Rotor;
10. Roller

Diagnostics of the ignition castle

The ignition castle refers to one of the most reliable and durable car units. In order, this unit is quite rare. Most often, the larvae and damage to the elements of the contact group occurs in the VAZ 2110 ignition lock. To determine the true cause of the malfunction of the ignition lock, it is necessary to make it diagnostics.

To diagnose the ignition lock, we need a multimeter.

And so, the diagnosis of the VAZ 2110 ignition lock is as follows:

1. From the steering wheel column, remove all the decorative panels;
2. With the help of a multimeter, we check output contacts in different positions of the key;
3. So at the 0th position of the key in the VAZ 2110 car ignition lock, the voltage must only be fed to 8 and 30 contact;
4. When turning the key in the 1st position, the voltage is fed to the following electrons (rear window heating, headlights, turn signals, overall lights, fan stove, glass player, wiper, cigarette lighter);
5. When turning the key in the 2nd position, the voltage also begins to be supplied to all other electroborers designed to operate the engine;
6. When turning the key to position 3, the voltage is fed to the 50th contact, namely the starter. In this case, the key automatically should be returned to position 2 with a spring.

Repair of the ignition lock by car VAZ 2110

Finding out the fault that arose in the car ignition lock and in the absence of the possibility of repairing with a soldering. Repair is performed using the direct replacement of the faulty item. As mentioned earlier - this is usually the larvae or the contact group of the ignition lock.

To repair the VAZ 2110 Car Ignition Castle, we will need the following tools.

tools assistants

• Crosshead screwdriver;
• Thin screwdriver (hour);
• Key on "10"
• A small hammer;
• Passatia;
• Chisel.

castle larva replacement, step-by-step instructions

Replacing the larvae of the ignition lock on the VAZ 2110 car is made in case of its direct damage, snacking, etc. As a rule, such problems appear after long-term operation of the vehicle or in the case of a hijacking.

And so, the replacement of the larvae of the ignition castle on the VAZ 2110 car is made in the following sequence:

1. Remove the terminal with the battery (to deraid the ignition lock);
2. Remove the casing from the car steering column;
3. Unscrewing the ignition lock fastening bolts;
4. Pull the ignition lock (so that it would be convenient to work);
5. Gently stretch the pin on the side, it holds the larva of the ignition lock (it is easiest to pull it out with a thin screwdriver and a small hammer);
6. Stretching the larva, install a new one;
7. Check the performance of the ignition lock;
8. Check the steering wheel lock adjustment when you turn;
9. Adjust blocking (if necessary);
10. We collect everything into place.

replacing the contact group of the ignition lock, step by step instructions

After the diagnosis in the event of a malfunction in the operation of the contact group of the ignition lock directly. You can replace only it. The contact group of the ignition lock is as well as the larva is replaced by a part and sold in auto shops.

And so, replacing the contact group of the ignition lock by car VAZ 2110, produced in the following sequence:

1. Remove the terminal with the battery (to deraid the ignition lock);
2. Remove the casing from the car steering column;
3. We unscrew or bring up the hammer with the chisel the ignition lock fastening bolts;
4. Remove the plastic cover from the ignition lock;
5. Disconnect all contacts (before turning off it is recommended, to move them to avoid confusion in the future);
6. With a screwdriver, two latches are resting;
7. We take out the contact group;
8. Install a new contact group;
9. We collect everything in the reverse order.

Ignition Castle 2110, change the lock completely, step by step instructions

Perform a complete replacement of the ignition lock by car VAZ 2110, many times easier and faster than changing separate parts.

And so, the full replacement of the ignition castle on the VAZ 2110 car is made in the following sequence:

1. Remove the terminal with the battery (to deraid the ignition lock);
2. Remove the casing from the car steering column;
3. We unscrew or bring up the hammer with the chisel the ignition lock fastening bolts;
4. Disconnect the ignition lock plug;
5. Change the ignition castle;
6. We collect everything in the reverse order.

How to choose high-quality ignition lock for car VAZ 2110

There are many fakes on the automotive spare parts market. This problem has not bypassed the ignition lock. In order to purchase a high-quality ignition lock in the auto shop, when choosing, you need to pay your attention to the following signs.

Quality ignition castle for car VAZ 2110:

• Wide holographic sticker (when trying to tear it off);
• The housing is neat and smoothly tightened;
• Easy, without effort is inserted and the key is pulled out;
• Neat and dense packaging;
• Light steering wheel lock tongue.

Tips of professionals

• Every year the replacement of the larvae and the contact group of the ignition lock is becoming less relevant. This happens for the reason that much more reliable, more convenient and faster to fully replace the ignition lock.
• Despite the seemingly prostate, the replacement of the contact group or the larva of the ignition lock. Pretty labor-intensive process, with no confidence in their abilities, it is better not to take it.
• Often, when the ignition lock larva, the usual lubrication is helps. For lubrication of the larva, the ignition lock is best suited graphite lubricant.
• To avoid faults in the ignition lock after it is directly replaced. It is necessary to install only the original ignition lock. This is the key to the fact that it will serve you for a long time.